Why optical coupling?
The optical coupling performs an important task in the case of a compound of an optical cable, as well as to organize the required optical fiber network topology.
In practice, the coupling often perform the functions of distribution crosses. Consequently, the choice of optical coupling is a matter of responsible and requires careful accounting for many factors.
So, before proceeding with the choice of optical coupling, you must accurately decide on its future location - this is a very important factor. Couplings can have completely different form factors, and you need to choose only one of the many options. If the alleged arrangement of the coupling is the lighting support, LEP, etc., it is best to apply compact clutches - they are easy to position on the support beautiful, not disturbing the aesthetics of the appearance. For such an option, it is recommended to use a dead-end coupling of the Item type or the HYC-H couplings from the Chinese manufacturer. In practice, such couplings have proven themselves very well, and are very convenient when making installation and dismantling.
Why is it more expedient to use a mockey hub? Such couplings are used everywhere used by providers-highways (Transtelecom, Rostelecom) on their supports, as well as in places where optics was welding. They are beneficial to the fact that cable entries in them are located below, almost 100% excluding the penetration into the water clutch. In addition, such a coupling can be easily disassembled and gather again when conducting periodic maintenance.
When laying the fiber optic network in telephone sewers, and the future location of the coupling is a telephone well, you are best suited for two types of couplings mentioned above.
You can add clutches to them. This is a rather good shortened coupling. Usually, the clutches have a length of about 80 cm. If adding the output of the cable attached with the help of a shrink tube to this, it turns out a vague design of length 1, 2 meters. Such a design is quite difficult to put in the well and in addition to this, the cable also placed there. So some coupling can create some difficulties when placed in a well.
So, we considered the rules for choosing optical couplings, depending on the intended placement, but the last word is yours. Optical couplings are widely represented in the market of fiber optic communication lines, however, like all kinds of equipment, cables, including optical sound cable, communication cable, etc. pin-up-casino.info.tr
In practice, the coupling often perform the functions of distribution crosses. Consequently, the choice of optical coupling is a matter of responsible and requires careful accounting for many factors.
So, before proceeding with the choice of optical coupling, you must accurately decide on its future location - this is a very important factor. Couplings can have completely different form factors, and you need to choose only one of the many options. If the alleged arrangement of the coupling is the lighting support, LEP, etc., it is best to apply compact clutches - they are easy to position on the support beautiful, not disturbing the aesthetics of the appearance. For such an option, it is recommended to use a dead-end coupling of the Item type or the HYC-H couplings from the Chinese manufacturer. In practice, such couplings have proven themselves very well, and are very convenient when making installation and dismantling.
Why is it more expedient to use a mockey hub? Such couplings are used everywhere used by providers-highways (Transtelecom, Rostelecom) on their supports, as well as in places where optics was welding. They are beneficial to the fact that cable entries in them are located below, almost 100% excluding the penetration into the water clutch. In addition, such a coupling can be easily disassembled and gather again when conducting periodic maintenance.
When laying the fiber optic network in telephone sewers, and the future location of the coupling is a telephone well, you are best suited for two types of couplings mentioned above.
You can add clutches to them. This is a rather good shortened coupling. Usually, the clutches have a length of about 80 cm. If adding the output of the cable attached with the help of a shrink tube to this, it turns out a vague design of length 1, 2 meters. Such a design is quite difficult to put in the well and in addition to this, the cable also placed there. So some coupling can create some difficulties when placed in a well.
So, we considered the rules for choosing optical couplings, depending on the intended placement, but the last word is yours. Optical couplings are widely represented in the market of fiber optic communication lines, however, like all kinds of equipment, cables, including optical sound cable, communication cable, etc. pin-up-casino.info.tr
